build.irieelectronics.de
control – Euxoloti build
http://build.irieelectronics.de/control-build
Checkup & calibration. Troubelshooting & FAQs. R1, R2, R13, R19. R4, R6, R11, R14, R20. R3, R5, R9, R12. 2 Diode, IC Socket and ceramic cap. Keep in mind that the dark line on the 1N4148 body should line up with the silkscreen mark for correct polarization and the IC socket position should match the one on the silkscreen. 4 Pin Headers (core connection). 5 Pin Headers (USB connection). Male Molex pin header. Should match the labels on the silkscreen. 35mm socket for Eurorack modular synths. Buttons negat...
build.irieelectronics.de
checkup & calibration – Euxoloti build
http://build.irieelectronics.de/checkup-calibration
Checkup & calibration. Troubelshooting & FAQs. Checkup & calibration. 1 Axoloti Core Preparation. For the next step you will need a cool mind. The original Axoloti core layout is a bit to large for Euxoloti, so you will have to break off the Power/MIDI Part. Don’t worry though, its functionality is replicated by the Euxoloti. 2 Euxoloti Core Setup. If everything went well you can now hook up the Euxoloti core to your Eurorack power supply. At this point, leave out all ICs, the Axoloti and Maple Mini.
build.irieelectronics.de
core – Euxoloti build
http://build.irieelectronics.de/core-build
Checkup & calibration. Troubelshooting & FAQs. The following instruction should guide you through assembly and calibration process of your Euxoloti core. If you’re familiar with DIY assembly and you don’t need detailed instructions just click here. To jump straight to the calibration section. R1, R2, R9, R10, R21, R22, R32, R40. R5, R6, R15, R16, R26, R38. Don’t worry about the missing resistors. They will be soldered later. Because they’re mounted vertically. 4 Ferrite Beads and IC Sockets. The two trim...
build.irieelectronics.de
usb cable – Euxoloti build
http://build.irieelectronics.de/usbcable
Checkup & calibration. Troubelshooting & FAQs. For the next step you will need the following thing:. Some sort of male micro USB cable longer then 10cm (B). PCB connector (PSK) 5Pin Female jack (C). 5x Crimp contacts for PSK (A). Optional shrink tubing (dia to fit usb cable and one small 0,6mm for shield part) (D). Next, skin a short part of the isolation and connect a PSK crimp contact to each end. There are tools for this. In the end your modified USB cable should look like this:. We use cookies to ens...
build.irieelectronics.de
I/O routing – Euxoloti build
http://build.irieelectronics.de/io-routing
Checkup & calibration. Troubelshooting & FAQs. Your browser don’t support svg or objects. Euxoloti module uses an Axoloti. And Maple Mini which are transmitting their datas by serial ports to each other. The Axoloti PA2(TX)/PA3(RX) GPIOs can be used as an optional serial port. The Maple board uses serial port 3 PB10(TX)/PB11 for communication. Generell MIDI protocol. Is used. Basically it’s the same like connecting a MIDI device to Axoloti’s main MIDI I/O. ButtonState[x]) { buttonState[x] = buttonReading...
build.irieelectronics.de
gat8 – Euxoloti build
http://build.irieelectronics.de/gat8-build
Checkup & calibration. Troubelshooting & FAQs. 1 Resistors and Caps. R25, R26, R27, R28, R29,R30,R31,R32. R5, R6, R7, R8, R9, R10, R11, R12. R1, R2, R3, R4, R21, R22, R23, R24. 3 Diode, Ferrite Bead and IC Socket. Please, remember of diodes polarization and mount position. See yellow cycle for IC socket orientation. 5 90 male Headers. 2×5, 90 , pitch: 2,54,. 1×5, 90 , pitch: 2,54,. 6 3,5mm Jacks. OUT1, OUT2, OUT3, OUT4, OUT5, OUT6, OUT7, OUT8. LED1, LED2, LED3, LED4, LED5, LED6, LED7, LED8. Before you mo...
build.irieelectronics.de
maple mini – Euxoloti build
http://build.irieelectronics.de/maple-mini-stm32duino
Checkup & calibration. Troubelshooting & FAQs. The following instructions awill guide you through the stm32duino setup and bootloader flashing for Mac OSX. The stm32flash commands should be similar for Linux and Windows. If you have any problems with flashing bootloader just take a look at troubleshooting guide. Or visit the stm32duino Forum. First you need to download the following things:. Arduino IDE 1.6.5 or 1.6.9. 5 Add the MIDI library to the Arduino IDE. Boot0 (Pin “but”). 4 open Terminal and go t...
build.irieelectronics.de
troubelshooting & FAQs – Euxoloti build
http://build.irieelectronics.de/troubelshooting-faqs
Checkup & calibration. Troubelshooting & FAQs. Troubelshooting & FAQs. Can’t flash Maple Mini (Stm32F103CB) bootloader. First check your usb-serial maple mini connections ( boot pin states! Ensure that bootloader is placed at the right folder and you have selected the right serial port. Software from ST. It only runs on windows machine and an additional usb-serial converter is also required. No reaction from Pots, Buttons or LEDs. Or from Axoloti’s Community Library. First, don’t worry. You may need to s...
build.irieelectronics.de
more – Euxoloti build
http://build.irieelectronics.de/more
Checkup & calibration. Troubelshooting & FAQs. Checkup & calibration. Vega Wordpress Theme by LyraThemes. We use cookies to ensure that we give you the best experience on our website. If you continue to use this site we will assume that you are happy with it.
SOCIAL ENGAGEMENT