kullander.nu
Christian Kullander | News and thoughts
http://kullander.nu/blog
Skip to primary content. Skip to secondary content. December 23, 2014. Based on an old IKEA JULEN I created a WiFi enabled Christmas tree! The JULEN tree is at least 10 years old, probably older and has been sitting around in storage without seeing much use. The 10W halogen 2 W AC motor and ancient AC/AC transformer was a major reason. By using some WS2812B pixels and a Spark Core it can now be controlled from anywhere with an Internet connection and uses at most a fifth of the power! July 6, 2013. The a...
peterklemperer.com
Printrbot Jr. Unboxing | Pete's Projects
http://www.peterklemperer.com/blog/2012/10/03/printrbot-jr-unboxing
Peter Klemperer's personal pet projects. Printrbot Jr. First Print →. Printrbot Jr. Unboxing. October 3, 2012. Prints stick to the printer bed. 8211; maybe the z-stop is step to close to the bed. 8211; other tape might be better? 8211; See post by Lincomatic. 8211; Rep-rap dimensional calibration. Y-Axis motor pretty warm. Put clear tape over the jumper on the power supply. Find improved USB serial driver for the Mac OSX. Motors run for a few movements and then all stop. 8211; This appears to be just blu...
reprapsquad.wordpress.com
The Good And The Bad | RepRap Squad
https://reprapsquad.wordpress.com/the-good-and-the-bad
Skip to main content. Skip to primary sidebar. Skip to secondary sidebar. All Things Printrbot, All In One Place! Filaments and How They Work. Getting Started With 3D Printing. Printrbot Goes Completely OPEN SOURCE. RepRap News From Around The World. RepRap Squad’s Tips N Tricks. The Good And The Bad. The Printrbot Nintendo Edition. The Good And The Bad. Here’s the list so far:. 8211; Filament Supplier. 8211; Filament Supplier. Forums for quite sometime. If your looking for filament, check out their ...
reprapsquad.wordpress.com
All Things Printrbot, All In One Place! | RepRap Squad
https://reprapsquad.wordpress.com/all-things-printrbot-all-in-one-place
Skip to main content. Skip to primary sidebar. Skip to secondary sidebar. All Things Printrbot, All In One Place! Filaments and How They Work. Getting Started With 3D Printing. Printrbot Goes Completely OPEN SOURCE. RepRap News From Around The World. RepRap Squad’s Tips N Tricks. The Good And The Bad. The Printrbot Nintendo Edition. All Things Printrbot, All In One Place! 8211; Design Files That Have Been Released Into The Wild –. Here’s The Link:. New Jr V2 files: March 17th 2014. Jr V2 from Printrbot.
tanukifu.blogspot.com
Tanukifu: May 2012
http://tanukifu.blogspot.com/2012_05_01_archive.html
Tuesday, May 29, 2012. Finishing up the printrbot build. The x-axis on the printrbot. Is driven by a belt. Rather than having a fixed loop, the ends are attached to the carriage directly (I'm uncertain how it was intended, but it seemed to make sense to loop the ends this way and use zip ties to secure them. This ends up working surprisingly well (I will probably make special clamps for tensioning later). I'll look at the quality of the signals later but it's a good idea to check the current limits for t...
christiankullander.com
Christian Kullander | News and thoughts
http://www.christiankullander.com/blog
Skip to primary content. Skip to secondary content. December 23, 2014. Based on an old IKEA JULEN I created a WiFi enabled Christmas tree! The JULEN tree is at least 10 years old, probably older and has been sitting around in storage without seeing much use. The 10W halogen 2 W AC motor and ancient AC/AC transformer was a major reason. By using some WS2812B pixels and a Spark Core it can now be controlled from anywhere with an Internet connection and uses at most a fifth of the power! July 6, 2013. The a...
niftykeen.blogspot.com
Nifty Keen Stuff
http://niftykeen.blogspot.com/2012_05_01_archive.html
Henry Minsky's Notes About Nifty Keen Stuff. Saturday, May 26, 2012. Printrbot Plus assembly Instructions. I ordered a Printrbot 3D printer. And we are waiting for it to ship. I've been looking at the forum http:/ www.printrbottalk.com/forum/. For discussions, and wiki at http:/ www.printrbottalk.com/wiki/index.php? Posted by Henry # 1:46 PM.
3dptb.blogspot.com
3D Print: Technology & Business: Der billigste 3D Drucker der Welt im Eigenbau - ein Erfahrungsbericht Teil 1
http://3dptb.blogspot.com/2014/10/der-billigste-3d-drucker-der-welt-im.html
3D Print: Technology and Business. 3D Drucker Selbstbau , Rapid Prototyping, RepRap, Deltabot, Rostock, Kossel. Deutsches Forum 3D Drucker. Dienstag, 21. Oktober 2014. Der billigste 3D Drucker der Welt im Eigenbau - ein Erfahrungsbericht Teil 1. Der QU BD OneUP gilt als der derzeit billigste 3 D Drucker der Welt. Im Rahmen einer Kickstarter Kampagne. Wurde er Ende 2013 vorgestellt. Hier der damalige Trailer:. Hier die technischen Daten:. Billigster 3D Drucker der Welt im Eigenbau -Tag 5. Im Kit ist alles...