owen-gl.blogspot.com
OWEN-GL / GARTIN TECHNOLOGIES: Case Study Comparing the Solderability of a Specific Pb Free No Clean Paste in Vapor Phase and Convection Reflow (Part 2)
http://owen-gl.blogspot.com/2011/08/case-study-comparing-solderability-of.html
Lunes, 22 de agosto de 2011. Case Study Comparing the Solderability of a Specific Pb Free No Clean Paste in Vapor Phase and Convection Reflow (Part 2). Five of the Cu Blocks went through Vapor Phase Reflow and five of the blocks went throug. Convection Reflow. A separate Cu Block had three thermocouples (TC’S) attached to it and was used to set up the recipes of the thermal reflow processes. Boiling Fluid – 240 perfluorinated heat transfer fluid. Pre-Heat - Oven at 290°C for 175 Seconds. Figure 6 shows t...
owen-gl.blogspot.com
OWEN-GL / GARTIN TECHNOLOGIES
http://owen-gl.blogspot.com/2013/01/fluxes.html
Martes, 29 de enero de 2013. En este ariculo hablaremos un poco sobre los tipos de flux y sus caracteristicas principales. Es un químico que ayuda a expandir el mojado en los metales removiendo ligeramente la oxidación y. Protege la superficie de la re-oxidación durante la operación de soldadura. 191;Cómo funciona el flux? El flux refluye antes que la soldadura, limpiando y ayudando a activar el proceso de calentamiento. La oxidación se forma en todos los metales expuestos al aire. Flux extra debe ser ev...
owen-gl.blogspot.com
OWEN-GL / GARTIN TECHNOLOGIES: febrero 2010
http://owen-gl.blogspot.com/2010_02_01_archive.html
Martes, 16 de febrero de 2010. BGA - REWORK PROCESS. (Part 1). Rs have mistakenly delayed the incorporation of Ball Grid Array (BGA) pack. Nto their product desig. Ns because of concerns over increased cost and complexity. Inc. E considered. Some important considerations for successfully reworking BGAs will be examined. Suscribirse a: Entradas (Atom). GARTIN TECHNOLOGIES - MANUFACTURA ELECTRONICA. GARTIN TECHNOLOGIES (MANUFACTURA ELECTRONICA). Ver todo mi perfil. BGA - REWORK PROCESS. (Part 1).
owen-gl.blogspot.com
OWEN-GL / GARTIN TECHNOLOGIES: Solderability of Vapor vs. Convection Reflow (part 1)
http://owen-gl.blogspot.com/2011/07/solderability-of-vapor-vs-convection.html
Martes, 5 de julio de 2011. Solderability of Vapor vs. Convection Reflow (part 1). Case Study Comparing the Solderability of a Specific Pb Free No Clean Paste in Vapor Phase and Convection Reflow. Importance of Wetting Angle to Solderability. During wetting, spreading has a greater speed then bulk material flow and thus, the amount of solder material present has little influence on the wetting angle. The greatest factors affecting the wetting angle are the following:. Type of flux used. Ya john i also ag...
owen-gl.blogspot.com
OWEN-GL / GARTIN TECHNOLOGIES: octubre 2010
http://owen-gl.blogspot.com/2010_10_01_archive.html
Domingo, 31 de octubre de 2010. INSPECTION TO IMPROVE LEAD-FREE SOLDER TECHNOLOGIES (Part 2). X-ray imaging in detection of voids is helpful to a certain extent. A Digital Microscope should be considered to work alongside, and not in place of or as alternative inspection equipment. Manufacturers striving to gain the highest quality should consider X-ray and Digital Microscope equipment as a pair. Detecting voids is a helpful example of this relationship. Judgment of Defects by Exterior Inspection. Since ...
owen-gl.blogspot.com
OWEN-GL / GARTIN TECHNOLOGIES: enero 2010
http://owen-gl.blogspot.com/2010_01_01_archive.html
Martes, 12 de enero de 2010. Soldado de alambres termopares. Suscribirse a: Entradas (Atom). GARTIN TECHNOLOGIES - MANUFACTURA ELECTRONICA. GARTIN TECHNOLOGIES (MANUFACTURA ELECTRONICA). Ver todo mi perfil. Soldado de alambres termopares Los materiales te. Plantilla Ethereal. Con la tecnología de Blogger.
owen-gl.blogspot.com
OWEN-GL / GARTIN TECHNOLOGIES: julio 2011
http://owen-gl.blogspot.com/2011_07_01_archive.html
Martes, 5 de julio de 2011. Solderability of Vapor vs. Convection Reflow (part 1). Case Study Comparing the Solderability of a Specific Pb Free No Clean Paste in Vapor Phase and Convection Reflow. Importance of Wetting Angle to Solderability. During wetting, spreading has a greater speed then bulk material flow and thus, the amount of solder material present has little influence on the wetting angle. The greatest factors affecting the wetting angle are the following:. Type of flux used. Ver todo mi perfil.
owen-gl.blogspot.com
OWEN-GL / GARTIN TECHNOLOGIES: enero 2013
http://owen-gl.blogspot.com/2013_01_01_archive.html
Martes, 29 de enero de 2013. Requirements and Acceptance for Cable and Wire Harness Assemblies. Includes greatly expanded criteria for molding, potting, splicing, crimp contacts without insulation support, inline insulation displacement connectors, connectorization, rigid and conformable cable, flexible sleeving, broomstitching, testing, and more. The training and certification programs for Revision B are in development and targeted for release in April 2013. Contact joselmartinez@owen-gl.com. Protege la...
owen-gl.blogspot.com
OWEN-GL / GARTIN TECHNOLOGIES
http://owen-gl.blogspot.com/2013/01/ipcwhma-620b-requirementsand-acceptance.html
Martes, 29 de enero de 2013. Requirements and Acceptance for Cable and Wire Harness Assemblies. Includes greatly expanded criteria for molding, potting, splicing, crimp contacts without insulation support, inline insulation displacement connectors, connectorization, rigid and conformable cable, flexible sleeving, broomstitching, testing, and more. The training and certification programs for Revision B are in development and targeted for release in April 2013. Contact joselmartinez@owen-gl.com. FLUXES....