renatopenas.blogspot.com
peñas`s blogspot: The 5 Principles of Technical Writing
http://renatopenas.blogspot.com/2009/11/5-principles-of-technical-writing.html
Tuesday, November 24, 2009. The 5 Principles of Technical Writing. Always have in mind a specific reader, real or imaginary, when you are writing a report; and always assume that this reader is intelligent, but uninformed. Before you start to write, always decide what the exact purpose of your report is; and make sure that every paragraph, every sentence, every word, makes a clear contribution to that purpose, and makes it at the right time. Use language that is simple, concrete, and familiar. Http:/ per...
jefferson-technicalwriting.blogspot.com
Technical Writing
http://jefferson-technicalwriting.blogspot.com/2010/03/sr-flip-flops-symbol-for-sr-latch.html
Saturday, March 6, 2010. The symbol for an SR latch. The fundamental latch is the simple SR flip-flop. Also commonly known as RS flip-flop. Where S and R stand for set. Respectively. It can be constructed from a pair of cross-coupled NAND. The stored bit is present on the output marked Q. Normally, in storage mode, the S and R inputs are both low. Maintains the Q and Q. Outputs in a constant state, with Q. The complement of Q. If S is pulsed high. The next-state equation of the SR flip-flop is. When T is...
jefferson-technicalwriting.blogspot.com
Technical Writing: November 2009
http://jefferson-technicalwriting.blogspot.com/2009_11_01_archive.html
Tuesday, November 24, 2009. Five Basic Principles of Good Technical Writing. Always have in mind a specific reader, real or imaginary, when you are writing a report; and always assume that this reader is intelligent, but uninformed. Before you start to write, always decide what the exact purpose of your report is; and make sure that every paragraph, every sentence, every word, makes a clear contribution to that purpose, and makes it at the right time. Use language that is simple, concrete, and familiar.
renatopenas.blogspot.com
peñas`s blogspot: November 2009
http://renatopenas.blogspot.com/2009_11_01_archive.html
Tuesday, November 24, 2009. The 5 Principles of Technical Writing. Always have in mind a specific reader, real or imaginary, when you are writing a report; and always assume that this reader is intelligent, but uninformed. Before you start to write, always decide what the exact purpose of your report is; and make sure that every paragraph, every sentence, every word, makes a clear contribution to that purpose, and makes it at the right time. Use language that is simple, concrete, and familiar. Http:/ per...
jefferson-technicalwriting.blogspot.com
Technical Writing
http://jefferson-technicalwriting.blogspot.com/2010/03/jk-flip-flop-to-prevent-any-possibility.html
Friday, March 5, 2010. In most ways, the JK flip-flop behaves just like the RS flip-flop. The Q and Q' outputs will only change state on the falling edge of the CLK signal, and the J and K inputs will control the future output state pretty much as before. However, there are some important differences. After which this latch will not change again. This was not true of the RS flip-flop. Flip-flop. The lone T input is in fact the CLK input for other types of flip-flops. The JK flip-flop must. Be edge trigge...
jefferson-technicalwriting.blogspot.com
Technical Writing
http://jefferson-technicalwriting.blogspot.com/2009/11/five-basic-principles-of-good-technical.html
Tuesday, November 24, 2009. Five Basic Principles of Good Technical Writing. Always have in mind a specific reader, real or imaginary, when you are writing a report; and always assume that this reader is intelligent, but uninformed. Before you start to write, always decide what the exact purpose of your report is; and make sure that every paragraph, every sentence, every word, makes a clear contribution to that purpose, and makes it at the right time. Use language that is simple, concrete, and familiar.
jefferson-technicalwriting.blogspot.com
Technical Writing: March 2010
http://jefferson-technicalwriting.blogspot.com/2010_03_01_archive.html
Saturday, March 6, 2010. The symbol for an SR latch. The fundamental latch is the simple SR flip-flop. Also commonly known as RS flip-flop. Where S and R stand for set. Respectively. It can be constructed from a pair of cross-coupled NAND. The stored bit is present on the output marked Q. Normally, in storage mode, the S and R inputs are both low. Maintains the Q and Q. Outputs in a constant state, with Q. The complement of Q. If S is pulsed high. The next-state equation of the SR flip-flop is. When T is...
